Facebook Instagram Youtube Twitter

Condensation Modes – Types of Condensation

From a practical engineering point of view, condensation can be categorized according to several criteria.

In general, three distinct forms of condensation are observed:

  • Film condensation. In film condensation, the condensate wets the surface and forms a liquid film on the surface that slides down under the influence of gravity. Film condensation results in low heat transfer rates as the film condensate impedes the heat transfer. The thickness of the film formed depends on many parameters, including orientation of the surface, viscosity, rate of condensation, etc. The film increases the thermal resistance to heat flow between the surface and the vapor, and the rate of heat transfer is reduced because of this resistance.
  • Dropwise condensation. The condensed vapor forms droplets on the surface instead of a continuous film in dropwise condensation. Dropwise condensation can occur when the surface is nonwetting, or these droplets are taken away from the surface by external flow or gravity. The vapor is in direct contact with the surface over most of the area, and heat transfer rates are much higher (more than 3 – 10 times higher) as there is very little resistance for heat flow between the vapor and the surface. The droplets develop at nucleation sites (points of surface imperfections such as pit, scratch, and cavities) and grow in size as more vapor condenses on its exposed surface. For steam condensers, it is common practice to use surface coatings (silicons, Teflon, or waxes) that inhibit wetting and stimulate dropwise condensation. But coatings gradually lose their effectiveness due to removal, oxidation, etc. In practice, no surface is found to continue as nonwetting over any length of time. Since it is often difficult to maintain this condition in most engineering applications, using the value of heat transfer coefficients assuming dropwise condensation for design purposes is not advisable.
  • Direct contact condensation. DCC, direct contact condensation occurs when vapor is brought into contact with a cold liquid. As in jet condensers, the cooling water is sprayed on the exhaust steam, and there is direct contact between the exhaust steam and cooling water. The process of condensation is very fast and efficient, but here cooling water and condensed steam are mixed up. The advantages of direct contact condensation over the conventional processes using metallic transfer surfaces are due to the relative simplicity of design, less corrosion and scaling problems, lower maintenance costs, higher specific transfer areas, and higher transfer rates. Despite these advantages, jet condensers are not usual in thermal power plants, especially due to the loss of condensate.
film condensation

___________

dropwise condensation

___________

direct contact condensation

 
References:
Heat Transfer:
  1. Fundamentals of Heat and Mass Transfer, 7th Edition. Theodore L. Bergman, Adrienne S. Lavine, Frank P. Incropera. John Wiley & Sons, Incorporated, 2011. ISBN: 9781118137253.
  2. Heat and Mass Transfer. Yunus A. Cengel. McGraw-Hill Education, 2011. ISBN: 9780071077866.
  3. U.S. Department of Energy, Thermodynamics, Heat Transfer and Fluid Flow. DOE Fundamentals Handbook, Volume 2 of 3. May 2016.

Nuclear and Reactor Physics:

  1. J. R. Lamarsh, Introduction to Nuclear Reactor Theory, 2nd ed., Addison-Wesley, Reading, MA (1983).
  2. J. R. Lamarsh, A. J. Baratta, Introduction to Nuclear Engineering, 3d ed., Prentice-Hall, 2001, ISBN: 0-201-82498-1.
  3. W. M. Stacey, Nuclear Reactor Physics, John Wiley & Sons, 2001, ISBN: 0- 471-39127-1.
  4. Glasstone, Sesonske. Nuclear Reactor Engineering: Reactor Systems Engineering, Springer; 4th edition, 1994, ISBN: 978-0412985317
  5. W.S.C. Williams. Nuclear and Particle Physics. Clarendon Press; 1 edition, 1991, ISBN: 978-0198520467
  6. G.R.Keepin. Physics of Nuclear Kinetics. Addison-Wesley Pub. Co; 1st edition, 1965
  7. Robert Reed Burn, Introduction to Nuclear Reactor Operation, 1988.
  8. U.S. Department of Energy, Nuclear Physics and Reactor Theory. DOE Fundamentals Handbook, Volume 1 and 2. January 1993.
  9. Paul Reuss, Neutron Physics. EDP Sciences, 2008. ISBN: 978-2759800414.

Advanced Reactor Physics:

  1. K. O. Ott, W. A. Bezella, Introductory Nuclear Reactor Statics, American Nuclear Society, Revised edition (1989), 1989, ISBN: 0-894-48033-2.
  2. K. O. Ott, R. J. Neuhold, Introductory Nuclear Reactor Dynamics, American Nuclear Society, 1985, ISBN: 0-894-48029-4.
  3. D. L. Hetrick, Dynamics of Nuclear Reactors, American Nuclear Society, 1993, ISBN: 0-894-48453-2.
  4. E. E. Lewis, W. F. Miller, Computational Methods of Neutron Transport, American Nuclear Society, 1993, ISBN: 0-894-48452-4.

See above:

Boiling and Condensation